收藏本站
DS3153 Triple DS3/E3/STS-1 LIU Demo Kit
The ChipView software supports the following actions:
·
·
·
·
·
Toggle a bit. Select the register in the register map and then click the bit in the bit map.
Write a register. Select the register, click the Write button, and enter the value to be written.
Write all registers. Click the Write All button and enter the value to be written.
Read a register. Select the register in the register map and click the Read button.
Read all registers. Click the Read All button.
6) Set the TDSA and TDSB bits in each GCR register to transmit a 2 - 1 PRBS pattern.
BASIC DS3153DK CONFIGURATION
These example configurations provide a quick start to using the DS3153DK. The DS3153 and the DS3153DK can
be configured in many other ways. To set up other configurations, refer to the DS3153 data sheet and other
sections of this data sheet.
DS3 Configuration
1) On the system connector, jumper all three TPOS pins and all three TNEG pins to ground.
2) On jumpers JMP7 through JMP9, connect the center post to the INT post. This connects the DS3153’s TCLK1
through TCLK3 pins to an on-board oscillator.
3) Place jumpers JMP2 through JMP4 to connect the DS3153’s TCLK1 through TCLK3 pins to the on-board DS3
oscillator. Make sure JMP1 has T3MCLK connected to the DS3 oscillator. Make sure JMP6 has E3MCLK
connected to the E3 oscillator.
4) Press and release the DS3153 reset button on the DK board –OR– set and then clear the RST bit in each GCR
register. The reset default mode is DS3.
5) Clear the TTS bit in each TCR register and clear the RTS bit in each RCR register.
15
7) For each LIU port, connect the transmitter to the receiver using 75 W coax to configure an external local
loopback –OR– set the LLB bit in each GCR register to configure an internal local loopback.
8) Press the Read All button twice to update the display.
At this point the transmitter is generating a 2
15
- 1 PRBS pattern that is being looped back to the receiver. On the
7) Set the TDSA and TDSB bits in each GCR register to transmit a 2 - 1 PRBS pattern.
DS3153DK board, the PRBS LEDs should be lit, indicating PRBS sync. The TDM and RLOS LEDs should not be
lit. In the register map, the SR and SRL registers should contain all zeros.
E3 Configuration
1) On the system connector, jumper all three TPOS pins and all three TNEG pins to ground.
2) On jumpers JMP7 through JMP9, connect the center post to the INT post. This connects the DS3153’s TCLK1
through TCLK3 pins to an on-board oscillator.
3) Place jumpers JMP2 through JMP4 to connect the DS3153’s TCLK1 through TCLK3 pins to the on-board E3
oscillator. Make sure JMP6 has E3MCLK connected to the E3 oscillator. Make sure JMP1 has T3MCLK
connected to the DS3 oscillator.
4) Press and release the DS3153 reset button on the DK board –OR– set and then clear the RST bit in each GCR
register.
5) Set the E3 bit in each GCR register.
6) Clear the TTS bit in each TCR register and clear the RTS bit in each RCR register.
23
8) For each LIU port, connect the transmitter to the receiver using 75 W coax to configure an external local
loopback –OR– set the LLB bit in each GCR register to configure an internal local loopback.
9) Press the Read All button twice to update the display.
At this point the transmitter is generating a 2
23
- 1 PRBS pattern that is being looped back to the receiver. On the
DS3153DK board, the PRBS LEDs should be lit, indicating PRBS sync. The TDM and RLOS LEDs should not be
lit. In the register map, the SR and SRL registers should contain all zeros.
6 of 11
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DS3154DK KIT DEMO FOR DS3154
DS3170DK KIT DESIGN FOR DS3170
DS33R11DK KIT DESIGN FOR DS33R11
DS33Z41DK KIT DESIGN FOR DS33Z41
DS9097E# COM PORT ADAPTER
DS9097U-E25# ADAPTER COM PORT RS232 DB-25
DS9490R# IC BRIDGE USB TO 1-WIRE RJ11
DST1E1DK KIT DESIGN SCT T1/E1 DS21X5Y
相关代理商/技术参数
DS3153N 功能描述:网络控制器与处理器 IC Triple DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS3153N# 功能描述:网络控制器与处理器 IC Triple DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS3153N+ 功能描述:网络控制器与处理器 IC Triple DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS3154 功能描述:网络控制器与处理器 IC Quad DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS3154+ 功能描述:网络控制器与处理器 IC Quad DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS3154A2 功能描述:网络控制器与处理器 IC Quad DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS3154DK 功能描述:网络开发工具 DS3154 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V
DS3154N 功能描述:网络控制器与处理器 IC Quad DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray